// Sunflex Folding Sliding doors / Sunflex Sf80 Alu-clad Timber

The top of the range SUNFLEX SF80 can offer the best of both worlds with its solid timber to the inside (65mm), to match the look of your room and aluminium cladding to the exterior (15mm), to match the remainder of your windows.

Have you arrived straight at this page? Click here to read an introduction to Sunflex and an brief overview of the full range

Enjoy the benefits of the clean low-maintenance aluminium and the natural beauty and superior thermal qualities of wood.

* Suitable for Domestic and Commercial use
* Energy efficient - compliant with Building Regulations Doc. L
* Excellent thermal properties
* Severe weather rated – tested and certified
* Discreet finger safe gaskets
* Meets Association of British Insurers requirements
* Virtually maintenance free

The SF80 is manufactured from triple laminated solid timber sections to the inside. These sections have been stabilised at stress points and bonded back together with opposing grains, which creates added strength whilst preventing warping and twisting. The aluminium external clad has a WS (softline/rounded) edge profile to compliment conventional aluminium or UPVC windows.

TRACK OPTIONS
There are two choices of track; a standard stepped weathered track for a severe weather rated system or for added convenience and improved safety, an aluminium flush track recessed into the floor. This provides a level walkthrough with an uninterrupted floor finish, compliant to Doc. M of the Building Regulations for disabled access.

SECURITY
Shoot bolts
A high level of security is provided as standard, with an effortless, quick, smooth and easy operation. It consists of a two-point top and bottom shoot bolt mechanism, with additional central locking point to end Lead door. The locking system is incorporated within the framework within each intermediate panel, operated by an internal flush handle. The shoot bolt rods are manufactured in aluminium and linked by a corrosion resistant cam. In addition, they are capped with polyamide cones that prevent any metal damage to the tracks when locking, whilst compressing the panels tight against the top and bottom seals.

Five-lever key-locking cylinder incorporated within the profile
A five-lever Euro profile cylinder key lock and handles are fitted to the end lead door or single pass door where there are an odd number of panels, or to the first opening pair, in an even number of panels. These can be fitted to either the inside only or both internally and externally as required, meeting the requirements of the Association of British Insurers. By integrating the locking cylinder into the existing profile in this way eliminates the need for an additional add-on profile familiar with other sub standard systems, ensuring all sightlines remain symmetrically the same.

Added security options
Additional key locks can be added at every intermediate handle point for higher security. Mortice locks can be fitted where a latching position is required for added convenience. Panic locks can be fitted for fire escapes, electric latch-release locks and rollerball latch locks are also available for commercial use.

Inline glazed and locking hinge pins
A unique glazing system prevents the glass from being removed when the doors are in a closed position, with external centre secured locking hinge pins and interlocking external gaskets as standard.

WEATHER SEALS
The weathered track for severe conditions
A severe weather rated system is achieved with the weathered track option, providing a perimeter double-rebated seal. (The system achieves DIN 18055, Category C performance for wind loading and water leakage.)

The flush track
The bottom seal between the door and the flush track is via double, twin nylon brush piles separated by a twin fin seal, giving an effective seal. It is recommended that some form of a sunken drainage channel and a slope away from the doors be integrated, to avoid any pooling of water.

Discreet finger safe cushion gaskets
The double gasket seals between the door panels are continuous and of superior quality (consisting of long lasting APTK internally and interlocking EPDM externally). These bubble gaskets are finger safe, providing a cushion to minimise the effect if fingers were to be trapped.

OPERATING SYSTEM
The SF80 is a bottom running system, consisting of wheels which are manufactured from tough glass fibre reinforced polyamide set around a maintenance-free sealed bearing, giving quiet, smooth operation with optimum resistance to extreme temperatures. Each wheel and guide mechanism can carry up to 200 kilograms. The advantage with a bottom running system is that unlike a top running system, should there be any structural movement above, the doors will not snag. With a bottom running system the weight is at the base, enabling the guide at the head to have a degree of tolerance. The fact the wheels of the running mechanism sit high on the track minimises the risk of the operating system fouling should any dirt or debris build up in the bottom of the track.

Self-lubricating collar type bearings provide quiet operation without squeaking hinges.

FURNITURE
Handles and hinges are made of cast alloy, handles are sprung-loaded and flush-fitted to enable door panels to stack flat when fully opened. Optional lever handles are available upon request for single access door or lead doors. Alternatively there are a wide variety of aftermarket chrome and brass handles. Large ‘D’ handles and automatic door closures can be fitted, for commercial instances. Trickle vents of either 2500mm2 or 5000mm2 can also be incorporated with the addition of a 40mm add-on head profile; which can be colour-coded to suit.

Panel catch
In the situation of a single access or pass door, in an odd number configuration the panel is fitted with a heavy duty adjustable panel catch which prevents the door from swinging back round in high winds and also counter weights the door with the adjacent panel for effortless operation.

Pull handles
When the folding door system opens externally the intermediate panels are fitted with a moulded ‘D’ shaped handle, this is attached to the internal hinge between two even panels and sit neatly within the gasket line enabling the easy closure of the panels against the compression top and bottom gasket seal.

  •  
  • Sunflex SF45 Non-thermal Alu
  •  
  • Sunflex SF55 Thermal Alu
  •  
  • Sunflex SF55c alu-wood
  •  
  • Sunflex SF65/68 Timber
  •  
  • Sunflex SF70 Thermal Alu
  •  
  • Sunflex SF80 Alu-clad timber

  • Sunflex SF80 Section Details PDF

    The most commonly used Sunflex SF80 sections are on this PDF, however there are other details for special solutions..contact us for more information

     

  • Sunflex SF80 Installation Guide

    Sunflex SF80 Installation instructions can be found in the attached file. Whilst you can opt to fit the doors yourself, we recommend that our Sunflex Authorised approved installers carry out the wo... more

     

  • Sunflex SF80 Care&Maintenance

    Sunflex SF80 care&maintenence instructions are in this file. Sunflex recommend these instructions are followed to maintain your Sunflex guarantee and to ensure long lasting use of your products